Posts tagged with "carprog"

How to read and write Audi A4 eeprom HC12 in cluster

Purpose:

copy the immo information from a cluster to another
make the mileage follow with the immo information

If clone all eeprom content than the mileage is transferred too.

 

 

Model:

Audi a4 2001

 

Optional devices:

Digiprog3, or ecu programmers like XprogCarprogUPA USB programmer

 

Original cluster:

The Jaeger cluster barely works

audi-a4-2001-cluster

 

audi-a4-2001-cluster-1

audi-a4-2001-cluster-2

Suggestion:

read the pin code from both the Instrument and adapt it to the vehicle

 

What to do on pin 21 and 22 on the chip:

 pin-21-pin-22-on-audi-a4-chip

– With car ECU programmers:

Eprom.set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.
Buy yourself Xprog-M programmer, Carprog full, UPA USB.
Pin 21 and 22 jumper after programming or wait 10 minutes.

 

– with Digiprog 3:

 digiprog3-read-audi-mileage

Eprom,set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.

 

Reference:

Eeprom HC12 read and write to the other counter:

 

AUDI MM AB 8/2001 DIAGNOSIS / TACHO DIAGNOSIS

(Write down the exact ALWAYS old / incorrect Mileage)

The diagnostic port is in the driver’s footwell. Turn the ignition

on a vehicle. Connect plug ST16 the diagnostic port and the

DIGIPROG.

 

Select the program: cars / trucks – AUDI – MM 4 / 99- DIAG.

The DIGI PROG II shows you the old / incorrect Mileage.

Enter the new / correct Mileage and confirm this.

Should be then after programming on the speedometer 999999 KM give

The old / wrong KM value again so that the speedometer again the old /

false indicates KM. Now you build the speedometer and break it to the

see board. Solder the green and black wire to the same color marked

Arrows at. Now connect the blue and the green plug with

the speedometer and plug ST41 with the DIGI PROG (picture on the following page.)

Now select the program: cars / trucks – AUDI – MM 4/99 HC12.

The DIGI PROG shows you the old / incorrect Mileage. Enter the

new / correct Mileage and confirm this with the hook.

Now shows you the DigiProg II 5 min wait. Remove the connection

between the DigiProg and the speedometer, wait 5 minutes and build the speedometer

again. Alternatively, for 5 min. Wait, you can also like in the image on the

next page shows the pins 21 and 22 bridges.

audi-a4-hc12-eeprom-1

Here necessarily the board from any power supply (Digiprog3 v4.94,

external power supply, etc.), Pin 21 + 22 bridge, and then you can use the tachometer

Immediately reinstall.

audi-a4-hc12-eeprom-2

OBD365 disclaimer:

TRY AT YOUR OWN RISK

Thanks for all tech support from members’ share at cartechnology forum.

http://digiprog3digiprogiii.blogspot.com/2016/08/digiprog-3-v494-read-audi-a4-eeprom.html

How to install and activate Carprog full V8.21 online

Here is the instruction on installing and activating Carprog V8.21 perfect online version China clone on Windows 7 operating system by obdii365.com engineer.

 

Software version: V8.21

Free download carprog v8.21 perfect online software (Disable anti-virus software)

Optional operating system:

Windows XP, WIN7, WIN8, WIN10

 

How to install Carprog full 8.21 online version?

– guide via videos:

Part 1 – Carprog 8.21 activation & installation

Establish a new folder named “8.21” on Desktop

Copy all the files in carprog 8.21 DVD disk (E:) to the new folder “8.21” on Desktop

activate-install-carprog-v8.21-1

Open “Carprog v8.21” application

Send the hardware ID to the dealer to get the activation code

activate-install-carprog-v8.21-2

activate-install-carprog-v8.21-3

Run Carprog 8.21 interface automatically, then close it

activate-install-carprog-v8.21-4

Part 2 – Carprog v8.21 read EEPROM M35080

Automatically installing device driver software…

Reading device info…

Select EEPROM-> 93C 24C 95x v2.6

Click on the tool icon

Select M35-> 35080-> read/ verify, then click OK

activate-install-carprog-v8.21-5

Click the fourth icon on the top icon column for initialization

Initializing…

Reading…

Verifying…

Verify ok

activate-install-carprog-v8.21-6

activate-install-carprog-v8.21-7

Done!

Ps: Carprog V9.31 no need activation.

If you need to update your carprog full v4,v5,v6.8 or v7.28 to V8.21 online version,you can buy theV8.21 carprog main unit without buying the full 21 adapters.

http://blog.obdii365.com/2016/05/29/install-and-activate-carprog-v8-21/

Carprog V8.21 vs. Carprog v9.31 vs. carprog v7.28

Newer Carprog v9.31 and v8.21 has been released to replace 7.28 version at obdii365.com. Caprog v9.31 is the latest version with the plug-and-play feature and no need activation, while Carprog 8.21 highlights the online feature and the most vehicle coverage.

 

Carprog full v7.28 vs. carprog v8.21 perfect online version vs. carprog v9.31

Product Carprog with 21 adapters
Software version Carprog V7.28 Carprog V8.21 firmware version (SE53-B) Carprog V9.31 (SE53)
Serial number (S/N) 081105CAR001773I 150428CAR00542UA 081105CAR001773I
Online NO Yes, it’s the super onlineversion. NO
Activation Activation after delivery Activation after delivery Activation before delivery;

 

Directly use it

Operating system Win XP, Win 7 Win XP,Win7,

 

Win8,Win10

Win XP,Win7,

 

Win8,Win10

Vehicle coverage V7.28 carprog supportthe least models among the three versions. V8.21 Carprog’s firmware is authorized more cars so that it support the most vehicle models. V9.31 carprog supports more vehicle models than v7.28
Models coverage: caprog v8.21 > v9.31 > v7.28
Software All carprog versions above can work well with ECU-OPEL, OPEL CAN, PSG16, OPEC28 software.
Tokens automatically get token renew after it used up
Function Airbag reset —> BEST

 

Dashboard programming,

immo (read pin code),

MPU & EEPROM programming,

radio decoding.

User feedback Carprog v9.31 read and erase BMW EEPROM M35080
Conclusion Carprog v8.21 is the best option for the most vehicle coverage and online use, while carprog 9.31 as a plug-and-play kit, is more convenient to use.

 

Attachment: Carprog function list and adapter list

Carprog Airbag: 
S5.1 – VAG (Audi, VW, Skoda, Seat) Airbag Reset Tool
S5.2 – BMW Airbag Reset Tool
S5.3 – Mercedes Benz Airbag Reset Tool
S5.4 – FORD Airbag Reset Tool
S5.5 – GM Airbag Reset Tool by OBDII
S5.6 – CARPROG CR16 Airbag tool – Audi, Mercedes, Ford, Volvo
S5.7 – Renault Airbag reset tool
S5.8 – Peugeot Airbag Reset tool
S5.9 – Citroen Airbag Reset tool
S5.10 – Honda Airbag Reset tool
S5.11 – Audi Airbag reset tool by direct connection to EEPROM or MPU
S5.14 – Ford Airbag Reset tool by direct connection to EEPROM or MPU
S5.16 – Hyundai Airbag Reset tool
S5.17 – KIA Airbag Reset tool
S5.18 – Lexus Airbag Reset tool
S5.19 – Rover Airbag Reset tool
S5.21 – Mazda Airbag Reset tool
S5.22 – Mitsubishi airbag reset tool
S5.23 – Nissan Airbag reset tool
S5.20 – Mercedes Benz Airbag Reset tool by direct connection
S5.25 – Opel Airbag reset tool by direct connection
S5.27 – Saab Airbag reset tool by direct connection
S5.28 – Subaru Airbag reset tool by direct connection
S5.30 – Toyota Airbag reset tool by direct connection
S5.31 – Alfa Romeo Airbag Reset Tool
S5.32 – Fiat Airbag Reset Tool
S5.33 – Porsche Airbag Reset Tool
S5.34 – Suzuki Airbag Reset Tool
S5.35 – Volvo Airbag Reset Tool
S5.36 – Daewoo Airbag Reset Tool

  1. CarProg Dash:
    S7.1 – VAG CAN programmer
    S7.2 – CarProg Dashboard programming
    S7.3 – CarProg Dashboard programming package update
    S7.5 – Mercedes Benz ASSYST explorer
    S7.6 – VDO dash decrypt tool – Skoda Roomster, SuperB, VW Polo, Audi A3, A6, Allroad with 93C86 odometer change and PIN reading
    S7.7 – Ford odometer change by OBDII (by CAN)
    S7.8 – VW 2007+ by OBD – Golf, Passat, Eos, Touran, Tiguan, Octavia with Micronas by diagnostic
    S7.10 – VAG VDO dashboards by K-line OBDII diagnostic – VW T5, Passat B5, Skoda SuperB and others
    2J74YAUDI – Audi 2J74Y repair software for CarProg4. CarProg Immo:
    S4.1 – Toyota Key Programmer
    S4.2 – Lexus key programmer
    S4.3 – Daihatsu Key Programmer
    S4.4 – CarProg BMW Key programmer
    S4.5 – Mercedes Benz Key programmer
    S4.6 – RENAULT Megane/Scenic infrared key programmer
    S4.7 – Kessy tool – A8, Touareg, Phaeton, Cayenne PIN code reader
  2. CarProg Processor:
    S2.1 – CARPROG Motorola (Freescale) HC05 MPU programmer
    S2.2 – CARPROG Motorola (Freescale) HC11 MPU programmer
    S2.3 – CARPROG Motorola (Freescale) HC08 MPU programmer
    S2.4 – CARPROG Motorola (Freescale) 912 and 9S12 MPU6. CarProg Programmer:
    ST92 – ST92F120, ST92F150, ST92F250 internal EEPROM programmer

     

    7. CarProg Radio Code:
    S6.1 – CARPROG CC1
    S6.2 – CARPROG CC2
    S6.3 – CARPROG CCN
    S6.4 – Philips Car Radio decoder
    S6.5 – Renault Car Radio decoder by serial number
    S6.6 – Audi/VW/Seat/Skoda car radio decoding software
    RNS510 – Navigation decoding tool by Navi diagnostic

    CarProg Aaapters:

1: CarProg Main harware interface

2: A1 – OBD2 Adapter Cable (Inside have K-line and CAN bus switches. Use with all cars complained with OBDII standard)

3: D1 – Odometer-airbag Adapter  (Dashboard ,Airbag programming adapter )

4: A3 – Transponder Antenna ( Used with all CARPROG immobiliser software )

5: A10 – Motorola Adapter Cable  (Motorola MCU programing adapter )

6: A11 – BMW EWS Adapter Cable   ( Used with BMW Immo software )

7: A16 – Car radio Cable   ( Used for Opel, Renault, Peugeot, Citroen car radio made by Philips decoding)

8: A15 – Cable  (Used with D1 adapter ,Universal car dashboard and airbag programming adapter )

9: A17 – Honda Airbag OBD2 Cable  (Adapter for Honda airbag reset by OBDII )

10: A4 – Eeprom Adapter Cable   (Used for eeprom programming)

11: A5 – DIP8 Clip Cable   (DIP8 Clip for eeprom programming)

12: A6 – SOIC8 Clip Cable   (SOIC8 Clip for eeprom programming)

13: A7 – MB 38-Pin Cable   (Used with MB Airbag and dashboard software)

14: A8 – BMW 20-Pin Cable (Used with BMW airbag and dashboard software )

15: RNS510 Adapter Cable  (RNS510 radio decoding interface cable )

16: VOLVO FORD CAN 2006+ Cable   (Needed for airbag and dashboard programming)

17: FIAT CAN 2006 Cable   (Needed for airbag and dashboard programming)

18: C1 OBD2 Female Cable

19: USB Cable

20: Power cable

21: CD   (Software V9.31)

http://blog.obdii365.com/2016/05/23/carprog-full-v7-28-vs-carprog-v8-21-vs-carprog-v9-31/

MB Sprinter 95p08 eeprom and HC08 immo pinout

Car problem and symptom:
I have problems with a Mercedes Sprinter W903 2004 year.
I messed around with the Kirnzle tachometer and now suddenly i get start error and can not start the car.
I don’t know if the tachometer plays any role in this problem but i know the we had problems eith the battery few times because it got empty a few times and last tim3 was 15 minutes before this problem accrued. I have star bud does not show anything.

 

Cause:

The problem is battery.

 

Solution 1:

Read eeprom from ECU and HC08 immobox with EEPROM/MCU programer, Orange 5,Xprog or cheap option carprog full ecu programmer.

Here is the eeprom and immo pinout to Xprog m:

You need reading ecu eprom 95p08 and reading immo box HC08, and you need sprinter start error repair v1.3…

(pinout are provided by MH forum Mercedes expert.)

sprinter-5P08C3-pinoutXprog-Temic12 sprinter

Solution 2:

Just try to virginise the ECU and program it to the IMMO with MB Star diagnostic(MB SD Connect C4).No need to read the MCU only the eeprom.

or unlock ecu in memory 5P08C3 in address 1D0 04 0F write 00 00 and with Star diagnostic programming.

How to virginise?

5P08C3 in address 1D0: 04 0F write 00 00 and you have virgine.

 

Solution 3:

Cheapest solution emulator,no more immobox problem
carlabimmo or china clone

( Solution 3 has not been tested yet.)

 

Hope they helps.

http://obd365.blogrip.com/2016/05/11/mercedes-sprinter-w903-immo-battery-error/

Free download Carprog full v7.28 clone

Carprog full China clone Airbag reset, Odometer, Radio, Mileage, Dashboard, Immobilizer, Transponder programmer V7.28 software can be downloaded free here.

 

Software version: V7.28

Operating system: Windows XP (without anti-virus)

 

Carprog full v7.28 clone software free download

http://www.chinaautodiag.com/download/carprog%207.28.zip

 

Software including:

ECU-OPEL – OPEL login reader from motor hybrid ECU. Works with Bosch ME1.5.5, Siemens SIMTEC71, SIMTEC71.1, Delco Diesel, Delco Multec.
OPEL CAN – Opel ECU by CAN programmer – read/change mileage in EDC16, MT35E, HSFI 2.2 read PIN, reset ECU
PSG16 – Opel PSG16 diesel pump by OBDII – read/change mileage, read PIN, reset ECU
OPEC28 – Opel Siemens Simtec ECU Tool Advanced

carprog connection 1

Carprog full Airbag: 

S5.1 – VAG (Audi, VW, Skoda, Seat) Airbag Reset Tool
S5.2 – BMW Airbag Reset Tool
S5.3 – Mercedes Benz Airbag Reset Tool
S5.4 – FORD Airbag Reset Tool
S5.5 – GM Airbag Reset Tool by OBDII
S5.6 – CARPROG CR16 Airbag tool – Audi, Mercedes, Ford, Volvo
S5.7 – Renault Airbag reset tool
S5.8 – Peugeot Airbag Reset tool
S5.9 – Citroen Airbag Reset tool
S5.10 – Honda Airbag Reset tool
S5.11 – Audi Airbag reset tool by direct connection to EEPROM or MPU
S5.14 – Ford Airbag Reset tool by direct connection to EEPROM or MPU
S5.16 – Hyundai Airbag Reset tool
S5.17 – KIA Airbag Reset tool
S5.18 – Lexus Airbag Reset tool
S5.19 – Rover Airbag Reset tool
S5.21 – Mazda Airbag Reset tool
S5.22 – Mitsubishi airbag reset tool
S5.23 – Nissan Airbag reset tool
S5.20 – Mercedes Benz Airbag Reset tool by direct connection
S5.25 – Opel Airbag reset tool by direct connection
S5.27 – Saab Airbag reset tool by direct connection
S5.28 – Subaru Airbag reset tool by direct connection
S5.30 – Toyota Airbag reset tool by direct connection
S5.31 – Alfa Romeo Airbag Reset Tool
S5.32 – Fiat Airbag Reset Tool
S5.33 – Porsche Airbag Reset Tool
S5.34 – Suzuki Airbag Reset Tool
S5.35 – Volvo Airbag Reset Tool
S5.36 – Daewoo Airbag Reset Tool

carprog-airbag

3. CarProg Dash:

S7.1 – VAG CAN programmer
S7.2 – CarProg Dashboard programming
S7.3 – CarProg Dashboard programming package update
S7.5 – Mercedes Benz ASSYST explorer
S7.6 – VDO dash decrypt tool – Skoda Roomster, SuperB, VW Polo, Audi A3, A6, Allroad with 93C86 odometer change and PIN reading
S7.7 – Ford odometer change by OBDII (by CAN)
S7.8 – VW 2007+ by OBD – Golf, Passat, Eos, Touran, Tiguan, Octavia with Micronas by diagnostic
S7.10 – VAG VDO dashboards by K-line OBDII diagnostic – VW T5, Passat B5, Skoda SuperB and others
2J74YAUDI – Audi 2J74Y repair software for CarProg
carprog-dashboard
4. CarProg Immo:

S4.1 – Toyota Key Programmer
S4.2 – Lexus key programmer
S4.3 – Daihatsu Key Programmer
S4.4 – CarProg BMW Key programmer
S4.5 – Mercedes Benz Key programmer
S4.6 – RENAULT Megane/Scenic infrared key programmer
S4.7 – Kessy tool – A8, Touareg, Phaeton, Cayenne PIN code reader

carprog-immo

5. CarProg Processor:

S2.1 – CARPROG Motorola (Freescale) HC05 MPU programmer
S2.2 – CARPROG Motorola (Freescale) HC11 MPU programmer
S2.3 – CARPROG Motorola (Freescale) HC08 MPU programmer
S2.4 – CARPROG Motorola (Freescale) 912 and 9S12 MPU

carprog-mcu-ecu

6. CarProg 7.28 Programmer:

ST92 – ST92F120, ST92F150, ST92F250 internal EEPROM programmer

carprog-programmer

7. CarProg Radio Code:

S6.1 – CARPROG CC1
S6.2 – CARPROG CC2
S6.3 – CARPROG CCN
S6.4 – Philips Car Radio decoder
S6.5 – Renault Car Radio decoder by serial number
S6.6 – Audi/VW/Seat/Skoda car radio decoding software
RNS510 – Navigation decoding tool by Navi diagnostic

carprog-car-radio

CarProg full 21 Adapters:

1: CarProg Main harware interface
2: A1 – OBD2 Adapter Cable (Inside have K-line and CAN bus switches. Use with all cars complained with OBDII standard)
3: D1 – Odometer-airbag Adapter  (Dashboard ,Airbag programming adapter )
4: A3 – Transponder Antenna ( Used with all CARPROG immobiliser software )
5: A10 – Motorola Adapter Cable  (Motorola MCU programing adapter )
6: A11 – BMW EWS Adapter Cable   ( Used with BMW Immo software )
7: A16 – Car radio Cable   ( Used for Opel, Renault, Peugeot, Citroen car radio made by Philips decoding)
8: A15 – Cable  (Used with D1 adapter ,Universal car dashboard and airbag programming adapter )
9: A17 – Honda Airbag OBD2 Cable  (Adapter for Honda airbag reset by OBDII )
10: A4 – Eeprom Adapter Cable   (Used for eeprom programming)
11: A5 – DIP8 Clip Cable   (DIP8 Clip for eeprom programming)
12: A6 – SOIC8 Clip Cable   (SOIC8 Clip for eeprom programming)
13: A7 – MB 38-Pin Cable   (Used with MB Airbag and dashboard software)
14: A8 – BMW 20-Pin Cable (Used with BMW airbag and dashboard software )
15: RNS510 Adapter Cable  (RNS510 radio decoding interface cable )
16: VOLVO FORD CAN 2006+ Cable   (Needed for airbag and dashboard programming)
17: FIAT CAN 2006 Cable   (Needed for airbag and dashboard programming)
18: C1 OBD2 Female Cable
19: USB Cable
20: Power cable
21: CD   (Software V7.28)

Carprog full error “Damaged parts” solution

These are customer solutions to Carprog full V7.28 errors “Damaged parts -6 or 4” with detailed information like “Damaged parts – ARM7 +4 ARM7(master mcu) can’t be replaced contact seller to repair your device.”

 

Error:

Damaged parts -6

Damaged parts -4

Error message:

Damaged parts – ARM7 +4 ARM7(master mcu) can’t be replaced contact seller to repair your device.

carprog-Damaged-parts-1
Damaged parts -6

Demaged part -6 means you have broken mcz33290(ISO K Line Serial Link Interface)

carprog-Damaged-parts-3

If you look at 2 pictures when you click HW test you can see some ic-s with numbers on it, under 6 is mcz33290. You can take it from D1 adapter just for probe – there is mc33660 – its the same;

carprog-Damaged-parts-4

When the Carprog full  interface came with a problem “Demaged part -6”, tested with A9 and all was ok then.

 

Damaged parts -4

had a problem with my Carprog clone when connect it to computer and push “Hardware test”. the result is error in some “PIN” a final error is “Damaged 4 parts”.

carprog-Damaged-parts-2

Now make the A9 Adapter and everything will be OK in the end

carprog-Damaged-parts-6

carprog-Damaged-parts-7

carprog-Damaged-parts-8

carprog-Damaged-parts-9

carprog-Damaged-parts-10

Maybe, some guys may be unlucky if even do so. And that is another possible reason:

the Voltage is too large and heat is not good —> overheating then burn the 4th mcu chip. Replace the 4th chip using a heat gun or sent it back to seller to repair your carprog full.
NOTE: solutions above is from caprog users. You may be at risks to try it. Obdii365.com just offers information here but won’t be responsible for it. Good luck!

 

http://blog.obdii365.com/2016/04/06/solve-carprog-error-damaged-parts/

Update Carprog China Clone to V8.03

Here’s the customer solution to update Carprog full v7.28 China Clone ECU, car radios, Airbag, dashboards, immobilizers repair kit to new 8.03.

 

AT91SAM7s256

CARPROG-PACKAGE

Free download Carprog V8.03 update file:

http://ulozto.net/xZtJppoy/carprog-v80-rar  (PASS: CARPROG V80)

http://ulozto.net/xfpwpZJN/carprog-v80-rar  (PASS: 987654@2@2)

(Note: customer tested our Carprog clone well. You are own your risk.)

 

Operating system:

Windows XP

 

Language:

English only

 

Software included in Carprog:

ECU-OPEL – OPEL login reader from motor hybrid ECU. Works with Bosch ME1.5.5, Siemens SIMTEC71, SIMTEC71.1, Delco Diesel, Delco Multec.
OPEL CAN – Opel ECU by CAN programmer – read mileage in EDC16, MT35E, HSFI 2.2 read PIN, reset ECU
PSG16 – Opel PSG16 diesel pump by OBDII – read mileage, read PIN, reset ECU
OPEC28 – Opel Siemens Simtec ECU Tool Advanced

 

Update error – Carprog unlocked:

When you fail to update and your carprog is unlocked, please use J-link or J-tag to repair unlocked issues

carprog-j-link

Carprog function list:

http://blog.obdii365.com/2016/03/07/update-carprog-clone-to-v8-03-customer-solution/

Theme: Fresh Print by BlogBaker. Powered by BlogBaker.