Posts tagged with "Lonsdor K518ISE"

Lonsdor K518ISE Program Porsche Macan Smart Key by OBD

Here’s the step-by-step guide on programming smart key on a  porsche macan turboby using Lonsdor K518ISE key programmer.
Requirements:
2 keys to be programmed
Read BCM data before programming
Lonsdor K518 key programmer
lonsdor-k518ise-Macan-1
Guide:
Connect K518ise host with vehicle via diagnostic socket
Turn ignition switch to ON position
Come to Immobilization->Porsche->Macan->Macan Turbo->Smart Key->Program Smart Key
lonsdor-k518ise-Macan-2
lonsdor-k518ise-Macan-3
lonsdor-k518ise-Macan-4
lonsdor-k518ise-Macan-5
lonsdor-k518ise-Macan-6
Use programmer to read BCM (D-brights/1N35H EEPROM) data, i.e XprogVVDI Prog. Save it as. BIN format and import it into the customfile folder.
Press OK to upload bin file
lonsdor-k518ise-Macan-7
lonsdor-k518ise-Macan-9
Lonsdor K518 will display vehicle VIN, press OK to confirm
lonsdor-k518ise-Macan-10
Please do following:
1.All keys need to learn, otherwise it cannot start vehicle. Recommend to learn the original keys before learning new key (battery must be installed)
2. New key added must be the dealer key generated by car BCM data or key ordered by VIN code
3.Insert key into induction hole when learning key. For smart key, remove the mechanical flip key from keyhole and insert it into induction hole to program.
lonsdor-k518ise-Macan-11
lonsdor-k518ise-Macan-12
Turn ignition to ON
lonsdor-k518ise-Macan-13
lonsdor-k518ise-Macan-14
Communicating…please wait
Lonsdor K518ISE will display vehicle VIN and part number, press OK to confirm
lonsdor-k518ise-Macan-15
Identified number of programmed keys in car: 2
lonsdor-k518ise-Macan-16
Enter key number to be programmed, here we are going to program  2 keys
lonsdor-k518ise-Macan-17
Building communication
Current dashboard display: 02-00
Note: if the programming success, the dashboard  will turn on automatically
lonsdor-k518ise-Macan-18
lonsdor-k518ise-Macan-19
K518 shows current key ID and programming processing
lonsdor-k518ise-Macan-20
Insert new key into ignition switch
Current dashboard display: 02-01
Note: if the programming success, the dashboard  will turn on automatically
lonsdor-k518ise-Macan-21
lonsdor-k518ise-Macan-22
Remove key and insert 2nd key within 30 sec, turn ignition ON
lonsdor-k518ise-Macan-23
Lonsdor K518 shows 2nd key current ID and programming
lonsdor-k518ise-Macan-24
Remove key, all keys involved in programming need to click the unlock button once
lonsdor-k518ise-Macan-25
Program success
lonsdor-k518ise-Macan-26
Program smart key success will automatically generate remote
Test the new smart key
lonsdor-k518ise-Macan-27

How to use Lonsdor K518ISE to OBD Program Smart Key

Lonsdor K518ISE universal auto key programmer specialized on programming key for high-end cars by OBD that most key tools failed, incl. Volvo, Renault, Maserati, Ferrari, Peugeot, Citroen, and Toyota/Lexus smart key all key lost via OBD.

 

Look here:

 

Volvo (S40, S60, S80, XC60, XC90, C30, C70, V40, V60, V70) key programming.
Toyota/Lexus: smart key all key lost – via OBD ( without dismantle)
BMW CAS3/CAS3+/CAS3++: direct OBD programming
BMW CAS4/CAS4+: dismantle & read data programming
Maserati (2016 -New): smart key programming
Ford (2016 -New): smart key programming
Hyundai / Kia 46/47/8A smart key: PIN code reading via OBD, all key lost included.
Renault ( Megane, Koleos, Scenic) without PIN code key programming
VAG group 4th & 5th immobilizer system
Ferrari (458, F12, F149): direct OBD programming
Peugeot /Citroen: two ways to read PIN code & programming, all keys lost included.

 

Lonsdor K518ISE Key Programmer Full Car List

Lonsdor K518 Key Programmer User Manual

 

So, how does Lonsdor K518ISE key programmer works? Good or not?

It works perfect. Test reports.. Here are you go.

 

So far, tested on three cars:

Range Rover

Toyota LEXUS ES200

Volvo XC60

 

 

Now I’ll chip in some words with real photos uploaded here.

 

The first test

Lonsdor K518ISE OBD adds new keys to Range Rover: success

 

Step 1: Select a model: immo-> Land Rover-> Range Rover-> 2008-2015

Lonsdor-K518ISE-add-new-keys-to Range-Rover (1)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (2)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (3)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (4)

Step 2: Program smart keys via OBD: -> Smart key-> Add smart key

Lonsdor-K518ISE-add-new-keys-to Range-Rover (5)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (6)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (7)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (8)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (9)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (10)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (11)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (12)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (13)

Program another new keys

Lonsdor-K518ISE-add-new-keys-to Range-Rover (14)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (15)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (16)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (17)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (18)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (19)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (20)

Step 3: Test if the new keys work or not

Lonsdor-K518ISE-add-new-keys-to Range-Rover (21)

Lonsdor-K518ISE-add-new-keys-to Range-Rover (22)

New keys work as good as the original.Done!

 

 

The second test

Lonsdor K518 OBD program new smart keys to Toyota LEXUS ES200 by OBD when all keys are lost : success

Step 1: Backup EEPROM data:

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (1)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (2)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (3)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (4)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (5)

Step 2: Make emulator key:

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (6)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (7)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (8)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (9)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (10)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (11)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (12)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (13)

Step 3: Add smart key:

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (14)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (15)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (16)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (17)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (18)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (19)

Lonsdor-K518ISE-Toyota-LEXUS-ES200-All-Key-Lost (20)

Done!

 

 

The third test

Lonsdor K518ISE key programmer program Volvo XC60 smart key via OBD: success

 lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-01

Step 1: Read the security data of the CEM module

 

Volvo’s CEM are located under the co-pilot airbag on the left, remove the debris box

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-02

Read CEM data with RN-01 board:

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-03

Plug K518ISE host, adapter, and RN-01 board:

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-04

Note: the new/old CEM box looks the same, but with different circuits.

 

For the old version of the CEM box:

when opening the lid, in the back of the circuit board, please pay attention to the black column with blue circles, which are the four positioning points that need to match stably with the white column of RN-01 board.

Note: The circuit board is coated with insulating glue, it is required to use the washing plate water to wash off the blue area of the insulation coating in the contact point (solder joint) , or power can not go through , if the needle of RN-01 board is broken, it will do to wire in the corresponding locations.

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-05

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-06

For the new version of the CEM box:

the circuit is different, which requires to wire to read the anti-theft data

the wiring diagram

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-07

Connect power to read the data

Separate RN-01 board to the motherboard to prevent it from conduction

Welding cable shouldn’t be more than 15cm

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-08

 

Step 2: Read the security data of the KVM module

 

Volvo’s KVM modules are located after the rear box, in the upside of the right rear wheel position (for 16 S60L car, dismantle from the right rear door to the wheel direction);

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-09

Open the module cover

Use the washing plate water to wash off the blue area of the insulation coating, or power can not go through.

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-10

Read KVM data with FS-01 board:

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-11

The positions in red circle are the 8-pin insertion points of FS-01 board:

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-12

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-13

The connection of the K518ISE machine, adapter and FS-01 board:

lonsdor-k518ise-key-programmer-volvo-xc60-smart-key-14

The most important note:

To failures in Volvo KVM data reading (coz the chip model is different), please do as follows:

① Use programmer to read out the data (.bin file);

② Contact and send the EEPROM data to K518ISE after-sales service, the engineers will convert the data into a dedicated file;

③  Connect K518ISE with computer and put the dedicated file into “file —> feature_35” folder;

④ Following the operations to select the KVM data from the process.

 

Step 3: Program smart keys via OBD

Refer to the following notes:

  1. For 6 keys, duringoperation, you need to firstly insert the keyinto the key slot and then operate by following the directions.
  2. For key recognition failure, please make sure the smart keyis not locked, aslocked key cannot be programmed, the fresh new key generally will not be locked.
  3. K518ISE has identification& unlock functions, which will test and identify whether a key is an unused one or not. If the remote control is invalid after the key is programmed (on condition that the battery is well installed and the remote control frequency is correct), try to import the CEM security data to unlock the key and then program again.

Note: Only the key of this car or corresponding car can be unlock after reading the CEM security data.

4,When installing Volvo battery, please note that the two batteries are placed in an overlap way and separated by a white paper in the middle, so please do not just replace the above one.

Dismantling is very simple also , just remove the metal key, and gently pry with a not so sharp knife in the same place where the metal key lies.

Done!

 

 

 

In summary,

Lonsdor K518ISE is verified to program new (smart) keys through OBD. Works perfect.

www.obdii365.com

http://blog.obdii365.com/2017/10/11/lonsdor-k518ise-obd-program-new-key-no-issues/

Program Lamborghini LP560 Remote by Lonsdor K518

Guide to use Lonsdor K518 key programmer to program/add Lamborghini LP560 remote key by OBD. (same procedures are applied to LP550, LP570 Gallardo)




K518 English version-Lonsdor K518ISE is released. Will be available in Otc, 2017. 





Reference:


OBD Location: Under the steering wheel

Lamborghini-LP560-obd-location

Vehicle model: LP550,LP560  LP570 Gallardo
Lamborghini-LP560-1
Remote Key type:
lp560-remote
Dashboard type:
LP560-dashboard

Pin code: No need

Remote program: by Lonsdor K518ISE key programmer




Guide:


Step 1: Program remote

Connect K518 host with vehicle

Turn on K518ISE

Select Immobilizer->Lamborghini->LP560
turn-ignition-on

Turn ignition switch to ON position
turn-ignition-off

Turn ignition OFF and then turn it ON

Configuring... please wait
select-remote-position

Select a remote position to write key (4 position optional/available )

Communicating...
press-unlock-button

Press on the Unlock button of the remote key for 1s within 5s
remote-programmed

No you can see remote position 1 has been programmed

Processing...
program-success
Program remote success.



Step 2: Delete Remote


If 4 remote position are occupied, you can delete remote to program other remote again

Turn ignition switch to ON position

Turn ignition OFF and then turn it ON

Configuring... please wait
remote-position-2-programmed
Position 1 and 2 has been programmed
configuring
Communicating...
delete-success
Delete success.

www.obdii365.com
http://lonsdor-k518ise.blogspot.com/2017/10/lonsdor-k518-program-lamborghini-lp560-remote-key.html

How to use Lonsdor K518 to Program Volvo S60 Smart Key

This is the demo guide on programming Volvo S60 keyless smart key by using Lonsdor K518ISE key programmer.
Vehicle and Key Information:
Chip model: Dedicated chip(brand new)
Remote type:433 frequency
Key embryo no.:No.24/38
PIN code requirement:Dismantle & read CEM to backup security data and program
Remote generation:Program smart key complete, remote will automatically generated
Under the lower-left of the steering wheel:
volvo-s6-steering-wheel
Car model: Volvo S60
volvo-s60
Smart sensor-to-start key (6-button)
volvo-s60-key-1
Volvo’s CEM is basically located behind the storage box which is in front of the co-pilot seat
volvo-cem
Volvo’s KVM modules are basically located in the trunk, in the right rear wheel position
volvo-kvm 
Function
1. Add smart key: to add a smart key or program on all key lost;
2. Delete smart key: delete the already programmed smart key;
3. Read the CEM security data:  dismantle & read CEM to backup security data (this is a must before programming);
4. Read the KVM security data: dismantle & read KVM to backup security data (this is a must before programming);
5. Key identification and unlocking: to detect whether the key is a new unused one. If the remote control is invalid after programming (on condition that the battery has been installed and the remote frequency is correct), try to import the CEM safety data to unlock the key and program again after unlocking.
Note: it can only unlock the CEM safety data of the vehicle or the corresponding vehicle
6. Module identification: identify the body CEM / KVM module status, please do this before all the operation, this function can ensure the module status, and distinguish between full-keyless / half-keyless. In addition, when the safety data backup is completed, and the module has been installed where it should be, please perform “module identification” again just in case and then proceed programming.
Note:
1. When programming Volvo 6-button keys, please be sure to dismantle&read the CEM and KVM first, as to their location and how to read, please refer to the “Operation” or “Reference”
2.First time to use the adapter, you need to bind it with K518ISE. Go to the K518ISE home page and choose “Settings -> Bind adapter”, following the direction to finish binding. One K518ISE host can bind up to 5 adapters, and the bound adapter can not be bound to other K518ISE hosts. Once bound, no need to bind again.
3. For the 6-button key, you need to dismantle & read the CEM in the co-pilot storage box,as well as the KVM in the right trunk to backup security data.
4.Connection between Lonsdor K518ISE host, adapter and RN-01 board :
lonsdor-k518ise-volvo-s60-1
5. Read Volvo CEM please use RN-01 board:
lonsdor-k518ise-volvo-s60-2
6. Connection between K518ISE host, adapter and FS-01 board:
lonsdor-k518ise-volvo-s60-3
7. Read Volvo KVM please use FS-01 board:
lonsdor-k518ise-volvo-s60-4

Operation:

Module identification
Before all operation, please connect the car OBD to “Module identification”, which can detect the module (CEM / KVM) status, distinguish if the car is full key-less or half-key-less.
Test status results: (1) Installed. (Indicating that the corresponding module status is normal)
(2) No installation or communication failure. (That the car does not have the corresponding module, or the module status is abnormal)
After the backup of the safety data is completed, install back all the modules accordingly. Please do “Module identification” again, check to ensure that the module is well installed and in normal status. And then do programming operation.
Read CEM security data:
1. Volvo’s CEM are located under the co-pilot airbag on the left, the removal of the co-pilot glove;
Volvo’s CEM is basically located behind the storage box which is in front of the co-pilot seat
lonsdor-k518ise-volvo-s60-5
CEM boxes may have the same appearance, but the back of the circuit wire location is different, can be called type A and B .
lonsdor-k518ise-volvo-s60-6
Type A: open the lid, pay attention to the black columns in the blue circle on the back of the circuit board, those are four positioning points, stably match them respectively with the white columns on RN-01 board.
Note: The circuit board is coated with insulating glue, it is required to use the washing plate water to wash it off the blue area of the insulation coating in the contact point (solder joint) , or power can not go through, if the needle of RN-01 board is broken, it will need to wire in the corresponding locations.
(First time to use the adapter, please bind it with Lonsdor K518 ISE host, please refer to”Function”)
lonsdor-k518ise-volvo-s60-7
lonsdor-k518ise-volvo-s60-8
Type B: Its circuit is different from that of type B, it requires to wire to read immodata, please refer to below wire instruction:
lonsdor-k518ise-volvo-s60-9
lonsdor-k518ise-volvo-s60-10
Note: Connect power to read the data, it is required to separate RN-01 board to the motherboard to prevent conduction; welding line should not exceed 15cm.
lonsdor-k518ise-volvo-s60-11
Read KVM security data:
1. Volvo’s KVM modules are located in the rear of the car rear, right rear wheel position (16 S60L recommended from the right rear door to the wheel direction);
lonsdor-k518ise-volvo-s60-12
lonsdor-k518ise-volvo-s60-13
2. Open the module cover, you must first use the washing plate to clean the blue area of the insulation coating,
or power can not go through, please bind it with Lonsdor K518ISE car key progammer host, please refer to”Function”)
lonsdor-k518ise-volvo-s60-14
3. The points in the red area are the 8 pin insertion points on the FS-01 board:
lonsdor-k518ise-volvo-s60-15
lonsdor-k518ise-volvo-s60-16
Notice
Part of the Volvo KVM data read failure is because the chip model is different, then please:
① use the programmer to read out the data (.bin file);
② Please contact the after-sales (phone / QQ: 4009669130) and send EEPROM data to them, then the engineers will transfer the data into a special file;
③ Then please connect K518ISE to the computer, put the special file into the”file —> feature_35”folder;
④ Please continue programming to select the KVM data from the process.
Read KVM data with programmer:
lonsdor-k518ise-volvo-s60-17
Attention
1. When programming Volvo 6-button key, be sure to dismantle & read the CEM and KVM, as to their location and how to read them, please refer to the “Operation” or “Reference”.
2. It is required to bind the adapter when using it for the first time, you need to bind it with K518ISE. Go to the device home page and choose “Settings -> Bind adapter”, following the direction to finish binding. One K518ISE host can bind up to 5 adapters, and the bound adapter can not be bound to other K518ISE hosts. Once bound, no need to bind again.
3. For 5-button key, you only need to dismantle&read the CEM in co-pilot storage box to backup security data, for 6-button key, you need to dismantle&read the CEM in co-pilot storage box, as well as the KVM in the right trunk to backup security data.
4. For 6-button key, you need to first insert the key into the key slot and then operate according to the directions.
5. Check if the card is locked when it can’t be inhaled in the key slot, locked key can’t be inhaled, a new card generally will not be locked.
6. When install battery to Volvo models, please pay attention that the two batteries are overlapped, separated by a white paper in between, do not just replace the above one.
Disassemble is also very simple, remove the metal key, in the place where the key lies, please find a little knife with not too sharp blade, gently open it from the gap.

Lonsdor K518 Key Programmer Function and Car List

Lonsdor K518ISE key programmer is made by Lonsdor company which made Chinese version K518, CI600 Plus (SKP1000) and CI300. K518ISE has some surprises and new vehicle coverage, including a few volvos, cars Toyota/Lexus smart key all key lost via OBD, newer Renault, Maserati, Ferrari and many other makes.
Lonsdor-K518ISE-key-programmer
Pre-order Price: $1199 (will be available in the end of Oct. 2017)

Main Function of Lonsdor K518ISE:

Immobilization Key Programming
Odometer adjustment/mileage correction
Built-in-in Volkswagen 4th & 5th adapter
Free BMW FEM key programming
Built-in Chip & remote detection module.

Lonsdor K518 Main Features:

 The best car diagnostic tool based on Android
 WIFI networking ensures software upgrading more convenient.
 No need to plug memory card, or connect the computer with data cable, more flexible in online upgrading, updating and activating.
 With USB-B2.0 standard connector, OBD-II test cable integrated with the diagnostic connector function of the adapter.
 7 inches high brightness, high definition color IPS capacitive screen
 3800mAh polymer battery
 Support external memory expansion, better within 32G
  Update Online: Official website http://en.lonsdor.com/
setting-interface

Lonsdor K518ISE Key programmer Special Features:

Volvo (S40, S60, S80, XC60, XC90, C30, C70, V40, V60, V70) key programming.
Toyota/Lexus: smart key all key lost – via OBD ( without dismantle)
BMW CAS3/CAS3+/CAS3++: direct OBD programming
BMW CAS4/CAS4+: dismantle & read data programming
2016 -New Maserati: smart key programming
2016 -New Ford: smart key programming
Hyundai / Kia 46/47/8A smart key: PIN code reading via OBD, all key lost included.
Renault ( Megane, Koleos, Scenic) without PIN code key programming
VAG group 4th & 5th immobilizer system
Ferrari (458, F12, F149): direct OBD programming
Peugeot /Citroen: two ways to read PIN code & programming, all keys lost included.

Lonsdor K518 ISE  Immobilizer Car List:

Europe:
Audi, BMW, Benz, VW, Volvo, Citroen, Ferrari, Maserati, Fiat, Lamborghini, Jaguar, MG,
Land Rover, Bentley, Lancia, Opel, Peugeot, Porsche, DS, Renault, Alfa Romeo, Smart,
Borgward
America:
Cadillac, Chevrolet, Dodge, GMC, Buick, Hummer, Ford, JEEP, Lincoln, Mercury
Asia:
Honda, Hyundai, Isuzu, KIA, Lexus, Mazda, Mitsubishi, Nissan, Ssangyong, Subaru, Suzuki,
Toyota, Shigaoka Queen
China:
Iveco, Trumpchi, BYD, Geely, Chery, Great Wall, Young Lotus (Basically all Chinese car
models are included)
Odometer Correction Car List:
VW, Porsche, Ford, Jaguar, Land Rover, Mazda, Audi, Renault, Hummer, Hyundai, Kia…
Note: more high-end cars will be updated very soon.
Lonsdor K518 ISE key programmer work with the smart key emulator as below, need purchase alone:
SKE-LT: Smart Key emulator – Toyota/Lexus smart key for all key lost via OBD
Black:  SKE-LT-DST40(94/D4) -Supports 94/D4 smart key.
Red: SKE-LT-8A(88/A8)-Support 88/A8 smart key.
Green: SKE-LT-DST80(98)-Supports 98 smart key.
Blue: SKE-LT-8A(A9)-Supports A9 smart key.
k518ise-emulator-key

Lonsdor K518ISE Technical Parameter:

RFID:                                                          Support 125KHz ASK,134.2KHz FSK
CPU:                                                           ARM Cortex-A7 Quad-core Processor Speed 1.34GHz
Display:                                                      1024*600,7 inch IPS capacitive
Memory:                                                      eMMC 8G RAM 1G
Battery Capacity:                                       3800 mAh
Power Supply:                                           DC12V 1A
Power port:                                                5.5×2.1mm
OBD Port:                                                   OBD-II
Comm Port:                                               USB 2.0-type B
OBDII Protocols:                                       ISO15765,ISO9141,ISO14230,SAEJ1850,VW TP1.6 TP2.0 etc
KPROG:                                                     Support programming MCU and EEPROM on ECU circuit board.
WIFI Communication Distance:           10m
k518-adapters

Lonsdor K518 ISE Registration & activation

After system updating, you need go to registration&activation.
For new user, click Registration, input user name(email), name(min 2 char), password(min 6 char), email verification code and click YES to complete registration(if interrupted after registration is done, you will go to the System update–Registered user to proceed). Then go to Activation confirmation to continue.
After confirming activation, it will enter into Setup password interface, please set 6-digit numbers as your startup password. Then after information verification by Lonsdor (5-30 minutes, you can check the progress by clicking “Refresh” ), you will required to re-enter the password to verify, when you get the notification that verification successful, the whole process before using the device is complete.
Note
1. User name must be available email address, so that you can receive the verification code
from Lonsdor by email.
2. Please pay attention to the difference between the registration password (min 6 char) and the startup password(6-digit), the former will generally only used when registration, so please commit the 6-digit startup password into memory, as this will be required every time when you start the device.
3. The account will be bound to the corresponding device for life, other accounts can not log in your device and your account can not log in an registered or activated device either. 4. An account can be used to bind multiple new devices.

System update

After networking, the system will automatically updated to the latest version. There are 3 ways of system update:
 One key update: quickly update the new added or modified functions.
 APK update: this is used when the APK is updated.
 Force to update: this is used when the device is faulty or to retrieve data.
Theme: Fresh Print by BlogBaker. Powered by BlogBaker.